Видео

2024 Rust Oleum Truck Bed Coating is now $16.99 at Advance Auto and AutoZone. Found it for $12 at Menards. Amazing how much further $1 went 6 years ago. (2018)

I paid $18 for the regular rustoleum and it looks like reg spray paint. Rolling it with the stuff in the can is 100% better. Those sprays are junk

I like the texture of the Dupli-color as well. Too bad the products that give you texture also clog up easier. I went with basic Rustoleum ( looks like basic black spray paint almost no texture) and put a final coat of Rustoleum Pro on top and it's a little better. I tried the Harbor Freight version of spray bed liner--like the texture, but it clogged up almost from the get go.

I used the Dupli-color, and it was in a can and I rolled it on the floor of my 67 IH Scout and after 30 years- yup it's still holding on pretty good- FYI

This is exactly what I have been thinking about doing

I think the red button is for emergency breaking also

Soak your cans in hot water for about 30 minutes before you spray and you wont get those clogs as much.

Thank you for this video. I appreciate the "two year update". I watched yours and a couple others using this engine for a log splitter. Last week I put the same engine on my nearly 30 year old 20 ton Speeco splitter. (The original 5 hp Tecumseh finally quit, and I had already replaced the hydraulic pump on mine a few years ago.) The Harbor Freight (Predator) 5.5 hp price is up just over $200 now, FYI, and this is the ONLY vertical shaft engine they sell. Still a lot cheaper than any other engine I could find "in store". I too used wire to bypass/rig the throttle issues. Other than a minor hydraulic line re-route to avoid the new exhaust it was a direct bolt in for my splitter. The fuel line is pretty flimsy thin rubber on it, and I'll replace it soon with "real" fuel line (and a filter).

I like the way dupli color looks on the interrior.

Nice 👍 thinking about doing all my toolboxes inside and out.

Be nice if you actually tested the durability. Waste of my time.

Well I'm at the stage that i have to do my bed and from what I've seen this is the best way to go. When you put down your checker plat did you lay it in when the bed was upside down on the or right side up? Did you weld your strips each side before or after you lay down the checker plate ? Thank you for this video it 's very helpful for the average joe such as myself .

Great video, when you applied the brake it showed 48%. Were you driving or in gear ? When I apply my brake it flashes and goes to Zero. I have it set for 50 and I was in park. I called Hopkins but they were unsure. Thanks in advance.

Been trying to find out if i could use regular primer instead of the expensive epoxy primer they recomend - how is your truck bed holding up?

For the line that you didn't replace, would that one have to be replaced all the way back to the transmission? I destroyed it trying to get it off the radiator and it looks like one heck of a project to get a whole new line in back to the transmission.

To lift up the bed pan so you could Weld that support, instead of using a chain you could use a floor jack with a block of wood

Which one is NOT rubbery?

Older video but glad I found it. I thought I was going to have to replace the rubber hose as well.

What area ohio you in.? Im in newark ohio

I did the same thing. After running it the first day I went back out and it would not start. After trying a couple of days to try to get it to start I took the motor back off, fixed the old motor. Took the motor back to Harbor Freight and got my money back. There are some things that work well from Harbor Freight but there's also some junk. I've been back using the old motor for about 4 years now and still going

I used the regular Rustoleum spray on the bed of my Tacoma twenty years ago and it held up very well. I used my truck like a truck, not a mall crawler. I just resprayed the spots that got gouged. I just gave that 2003 Tacoma to my son two weeks ago! I also used it to paint the front and rear bumpers of my Chevy van and it holds up very well even after using the bumpers as steps. I haven't had to respray them yet.

That looks very professionally done. Where did you get the sheet metal from?

why not use all 3 triple the protection

Looks like pro has much less sheen. That true?

the main problem with ALL these " information " videos is one has to listen to 10 minutes of yammering to maybe get the answer you're looking for

great visual here.thanks.

Thanks for this video.

Do you have the part number? Or can you shared where you got this part. I just replaced the other side, but I can’t find the part you just replaced

how many hours did this take you

What did you use for the texture on the black paint after you finished?

Dupicolor was awesome I used in on my roof frame on my Ute. Bloody awesome. Never had issues with clogging. But with rustoleun the can was bounce the size of duplicolor and the can would use up very quickly. Highly recommend duplicolor.

Replacing my Subaru engine on my airens 22 ton . Definitely like the video

haha! I was wondering the same thing about that green paint. I assume it's weldable primer at least?

I think for the money and the least amount of problems applying my bet is with the Restroleum Pro! There’s nothing worse then spraying and being interrupted with cleaning the tip every minute or two. It affects your application and eventual looks and coverage! I’m going with Restroleum Pro! Restroleum Spray products have never let me down!

Video sucks

You didn’t use enough tape.

I used that same engine as a replacement on my pressure washer. It was easy to remove the engine break just pull off the engine cover to access it and I left the lever in place as the electrical kill switch. I put a small light duty spring on it for engine shut down I just push the lever forward for a half second that grounds out the ignition to kill the engine with no engine break to disrupt operation . the whole job took me ten mins. Engine runs great pressure washer is like new

Did the dupli color have a higher gloss??

My floor panels have rotted out as well as the crossmembers. I’m replacing them. My question is does anyone know where I can get the bolt locations for the bed bolts?

Really good video 👍❤❤❤❤❤❤❤❤❤❤❤❤

Rust-Oleum pro is also sound detening

Not my style to be honest. I do the shadow foam (made from eva mats or yoga mats, plus something else new Im cooking up). I would have cleaned and polished that box up. its nice, and deserves a nice wax, and some metal polish on the handles.

As far as looks I like the dupli colod

where are you located ?

Like magic

Are those flexible?

I'm doing this with mine! thank you!!!!

hey from which states you are.?

How about adding a scratch test; a heat test; and an acid test to see how they all do?